MXS Twitter
-
- Posts: 152
- Joined: Fri Jul 01, 2011 3:03 am
Re: MXS Twitter
Screw mornings -_-
Andrew Schettley #519
2012 Limited Decal Fall Series C Class Champion
-
- Posts: 3275
- Joined: Tue Apr 12, 2011 9:36 pm
- Team: TBR
- Location: New Jersey
Re: MXS Twitter
on my way to school for the first time since october and the surgery. definately is bittersweet. 


Re: MXS Twitter
Who are the people on Tekkit going to play with now?
Re: MXS Twitter
Good choice. Ford made that mistake back in 07-08 on the 4.0s, heads would warp at like 70, 000 mi. we charge 2400 $ to do one. Most of that if for the machine shop working the heads. Honestly though I dont see it on that yota motor too often. But man that motors a dog! 22 way betterBallsfalsky wrote:scratch that, Wont be getting a 3.slo. Notorious for HG problems. What happens is the headgasket slowly lets go due to 1. The crossover pipe on the headers is extremely close to cyl #6, which super heats the gasket in that location and also the cylinder. They gasket warps and as I said before, slowly lets go. Because it slowly lets go, the block and heads often warp due to disagreeing expanding properties between the two(block is cast iron and the heads are aluminum). So pretty much if the gasket is gone, its almost guaranteed that the head and block will need to be resurfaced. Thats also very risky, because they can only be machined so much before they are un-usable. Its a shame... That truck is so clean...
Looks like I'll be looking for the same truck with a 22re.
Re: MXS Twitter
This is a block of text that can be added to posts you make. There is a 255 character limit.
-
- Posts: 1226
- Joined: Tue Jul 27, 2010 9:28 am
- Team: Spazztic
- Location: Estonia
Re: MXS Twitter
First video,with my friend lolol
-
- Posts: 2981
- Joined: Mon Feb 28, 2011 4:35 am
- Team: Tim Hortons
Re: MXS Twitter
145HP/160ft-lbs out of a 3.0 V6... Thats less power than a civic with the same fuel economy as a 350 small block... The reason the head gaskets go is 1. because the US banned asbestos HG's (and Toyota had to makeshift a metal one), and 2.The Vehicles that the HG's go in are mainly from the Cali plant. The Cali plant was not torquing the heads down properly. They were supposed to be torqued to spec, turned another 90 degrees, and then yet another 90. They were only torquing them to spec at that plant...DK662 wrote:Good choice. Ford made that mistake back in 07-08 on the 4.0s, heads would warp at like 70, 000 mi. we charge 2400 $ to do one. Most of that if for the machine shop working the heads. Honestly though I dont see it on that yota motor too often. But man that motors a dog! 22 way betterBallsfalsky wrote:scratch that, Wont be getting a 3.slo. Notorious for HG problems. What happens is the headgasket slowly lets go due to 1. The crossover pipe on the headers is extremely close to cyl #6, which super heats the gasket in that location and also the cylinder. They gasket warps and as I said before, slowly lets go. Because it slowly lets go, the block and heads often warp due to disagreeing expanding properties between the two(block is cast iron and the heads are aluminum). So pretty much if the gasket is gone, its almost guaranteed that the head and block will need to be resurfaced. Thats also very risky, because they can only be machined so much before they are un-usable. Its a shame... That truck is so clean...
Looks like I'll be looking for the same truck with a 22re.
For the people who JB'd using evasi0n yesterday: DO NOT INSTALL ZEPHYR! It will soft brick your phone if you go to restart it, and you will need to restore and re-JB your device, and also re-download all of your tweaks, themes, etc. I spent 5+ Hours getting my phone how I wanted it last night too... Goddamnit.
Re: MXS Twitter
I have this essay to write, have Crysis to play, and have Sim to watch. Not a bad combo, but I could do without the essay.
| 2013 MotoOption Supercross 250 Eastside Champion | #turnbarcrew |
-
- Posts: 2981
- Joined: Mon Feb 28, 2011 4:35 am
- Team: Tim Hortons
Re: MXS Twitter
I just remembered I pushed some bitch down the stairs at the last cabin party I went to... Just thought i'd share that...

The girl on the right...
Oh and the girl on the left is a dime piece.
The girl on the right...
Oh and the girl on the left is a dime piece.
Re: MXS Twitter
Balls you should probably go down and check yourself in to the old crowbar hotel for a while, FFS...
-
- Posts: 8401
- Joined: Thu Nov 19, 2009 5:52 am
- Team: Havoc Racing
- Contact:
Re: MXS Twitter
Is that how you want to present yourself, or is that taken more lightly in Canada too?Ballsfalsky wrote:...I pushed some bitch down the stairs...
jlv wrote:If it weren't for Havoc I'd have been arguing with the 12 year olds by myself.
Re: MXS Twitter
Nope, not taken too lightly. That kinda behaviour usually leads to a trip to the dentist around here
Re: MXS Twitter
What compels someone to say or even do something like that. That's fucked up.