Upcoming Models #2

Andy_Hack · Post by **Andy_Hack** » Sat Aug 18, 2012 11:06 am

mxsisboss wrote:DP Here it is so far,

yep needs defently the hole

Sandhapper · Post by **Sandhapper** » Sat Aug 18, 2012 11:51 am

Oh you ment the hole in the shroud? My bad. I model that hole too, but not those small holes if you know what I mean..

mxsisboss · Post by **mxsisboss** » Sat Aug 18, 2012 12:11 pm

Some progress

Motofinne #375 · Post by **Motofinne #375** » Sat Aug 18, 2012 1:04 pm

this is just my opinion, you don't need to post an "update" after you've done the forks. I hope you understand what i'm saying

mxsisboss · Post by **mxsisboss** » Sat Aug 18, 2012 1:11 pm

Engine, width and shroud fix...

mxsisboss · Post by **mxsisboss** » Sat Aug 18, 2012 1:13 pm

PArt of front fender as well

saetta · Post by **saetta** » Sat Aug 18, 2012 3:33 pm

can someone help me??

why is it showing like this? made the racetech hanguards and exported them..

for frame and stuff like that i used the standart .jm`s..

and these are the reason why i posted this in upcoming models

760Liam · Post by **760Liam** » Sat Aug 18, 2012 4:11 pm

pm me. i'll help you out

m121c · Post by **m121c** » Sat Aug 18, 2012 4:14 pm

mxsisboss wrote:Some progress

It just me or does the outline of the shroud seem not to connect to the middle, at the top of the shroud theres a hole?

dudy#75 · Post by **dudy#75** » Sat Aug 18, 2012 4:24 pm

saetta wrote:can someone help me??
why is it showing like this? made the racetech hanguards and exported them..
for frame and stuff like that i used the standart .jm`s..
http://i1195.photobucket.com/albums/aa3 ... hot302.png
and these are the reason why i posted this in upcoming models
http://i1195.photobucket.com/albums/aa3 ... hot303.png

it looks like the axis have changed with the new export i had the same problem

mxsisboss · Post by **mxsisboss** » Sat Aug 18, 2012 4:28 pm

Yes there are two small holes i need to fix them.

paulr093 · Post by **paulr093** » Sat Aug 18, 2012 4:37 pm

Is the frame that small at the bottom?

mxsisboss · Post by **mxsisboss** » Sat Aug 18, 2012 4:42 pm

Its about 95% correnct + i delete most of the sub frame to lower poly count and you wouldnt see it under the plastics anyways.

paulr093 · Post by **paulr093** » Sat Aug 18, 2012 7:07 pm

why would you do that? your upper and lower fork are going in different directions.

mxsisboss · Post by **mxsisboss** » Sat Aug 18, 2012 7:10 pm

I know i was giving my self a rough idea...

Upcoming Models #2

Re: Upcoming Models #2

Re: Upcoming Models #2

Re: Upcoming Models #2

Re: Upcoming Models #2

Re: Upcoming Models #2

Re: Upcoming Models #2

Re: Upcoming Models #2

Re: Upcoming Models #2

Re: Upcoming Models #2

Re: Upcoming Models #2

Re: Upcoming Models #2

Re: Upcoming Models #2

Re: Upcoming Models #2

Re: Upcoming Models #2

Re: Upcoming Models #2